Electronic

Mitsubishi CM10MD-24H New Stock

2021-08-29 die casting Comments Off

#CM10MD-24H Mitsubishi CM10MD-24H New CM10MD-24H is a 1200V (VCES) 10 Ampere CIB Power Module., CM10MD-24H pictures, CM10MD-24H price, #CM10MD-24H supplier
——————————————————————-
Email: [email protected]

https://www.slw-ele.com/cm10md-24h.html

——————————————————————-

CM10MD-24H Description

Powerex CIB Modules are designed for use in switching applications. Each module consists of a three phase diode converter section, a three phase IGBT inverter section and a brake section. All components and interconnects are isolated from the heat sinking baseplate, offering simplified system assembly and thermal management.

Features:

. Low Drive Power

. Low VCE(sat)

. Discrete Super-Fast

Recovery (70ns)

Free-Wheel Diodes

. High Frequency Operation

(20-25 kHz)

. Isolated Baseplate for Easy

Heat Sinking

Applications:

. AC Motor Control

. Motion/Servo Control

. General Purpose Inverters

. Robotics

Ordering Information:

Example: Select the complete nine digit module part number you desire from the table below – i.e.
Absolute Maximum Ratings, Tj = 25°C unless otherwise specified

Power Device Junction Temperature Tj -40 to 150 °C

Storage Temperature Tstg -40 to 125 °C

Mounting Torque, M4 Mounting Screws 13 in-lb

Module Weight (Typical) 60 Grams

Isolation Voltage, AC 1 minute, 60Hz VRMS 2500 Volts

CM10MD-24H is a 1200V (VCES) 10 Ampere CIB Power Module.

MFG Guide

MFG Guide

injection mold damage

2022-08-17 Chinaeye

It is safe to state that any given mold will require a certain amount of repair for damage occurring during the use or storage of that mold. The more it is used, or the longer it is stored, the more damage will occur. Damage that occurs during use includes items such as broken core or […]

MFG Guide

Failure mode, impact and criticality analysis and fault tree analysis

2022-08-17 Chinaeye

Reliability analysis technology In the reliability design of cnc machine tools, analysis is an important technical means. Reliability analysis is used to understand the defects in product design schemes, and to eliminate potential failure causes in the design stage through design improvements to achieve the purpose of design prevention. In the process of designing and […]

MFG Guide

HK movie mogul Run Run Shaw has died at age 107

2022-08-16 Chinaeye

Pioneering Hong Kong movie producer Run Run Shaw has died at the age of 107. No cause of death was given in a statement from Television Broadcasts Limited (TVB), which Shaw helped found in 1967 Born in Zhejiang Province near Shanghai, he rose to become what Variety magazine called a pioneer of the 20th century […]

MFG Guide

Four-column hydraulic press power sliding table hydraulic system

2022-08-15 Chinaeye

Four-column Hydraulic Press power sliding table hydraulic system Why should the blades of the hydraulic punch vane pump be inclined? What is the relationship between the inclination direction and the rotation direction of the rotor? Four-column hydraulic press hydraulic punching vane pump to ensure that the blades can reciprocate normally in the chute without blade […]

MFG Guide

A dust mask that can be reused

2022-08-15 Chinaeye

In general, the replaceable half face mask can only be replaced through DAO filter cotton and face mask accessories.It is beneficial to reduce the cost of respiratory protection.Now many OF KN100 level dust masks are reusable masks.Good protective effect, economical to use.Can effectively prevent pneumoconiosis. Due to the wide variety of masks on the market, […]

Cnc Machining

Cnc Machining

High-quality plastic parts can be manufactured using pyrometers

2022-06-26 Chinaeye

Plastic parts are vital in many different industries. New combinations of materials and manufacturing technologies are being developed, especially in challenging applications such as automotive engineering. Continuous fiber-reinforced thermoplastics are a common example of this innovation, which is extremely strong and lightweight at the same time. Automotive engineering is one such field, providing a series […]

Cnc Machining

How to measure the surface roughness of large parts?

2021-12-27 Chinaeye

Large parts, such as the engine block of emergency generators, construction machinery or ship engines; truck steering knuckles; or gears and bearings used in wind generators are usually too large and heavy to be performed on fixed roughness measurement equipment Measurement. Nevertheless, the roughness parameters must still be tested. In fact, roughness measurements on large […]

Cnc Machining

How to avoid bubbles or holes in the 3D printing manufacturing process?

2021-12-27 Chinaeye

Laser powder bed fusion is the dominant additive manufacturing technology and has not yet reached its potential. The problem facing the industry is that sometimes tiny bubbles or holes are formed during the printing process, and these holes form weak points in the final product. In the 3D printing process of parts, when the low-speed […]

Cnc Machining

How to choose the best grinding process for 3D printed parts

2021-12-27 Chinaeye

For metal production parts manufactured by additive manufacturing (AM), post-processing is usually required, especially on functional surfaces. Abrasive machining including grinding and polishing has the ability to finish machining conventional parts and additive parts (ie, 3D printed parts). Compared with mechanical processing (such as milling and other alternative finishing processes), grinding has the advantage of […]

Cnc Machining

Cooperative team to solve machine tool supply chain problems: 3D printing may be the first choice

2021-12-27 Chinaeye

A cooperative team from Oak Ridge National Laboratory solved the problem of the machine tool supply chain. The first step: 3D printing the largest casting. In remote laboratories, scientists and engineers representing public and private companies are working to restore and stabilize the dominance of American manufacturing. The purpose is not to solve the problems […]