Electronic

Mitsubishi CM20TF-12H New Stock

2021-09-20 Chinaeye Comments Off

#CM20TF-12H Mitsubishi CM20TF-12H New CM20TF-12H Six-IGBT IGBTMOD H-Series Module 20 Amperes 600 Volts., CM20TF-12H pictures, CM20TF-12H price, #CM20TF-12H supplier
——————————————————————-
Email: [email protected]

https://www.slw-ele.com/cm20tf-12h.html

——————————————————————-

CM20TF-12H Description

Manufacturer Part Number CM20TF-12H

Manufacturer Powerex, Inc.

Description IGBT MOD 6PAC 600V 20A H SER

Lead Free Status / RoHS Status Contains lead / RoHS non-compliant

CM20TF-12H Datasheets

CM20TF-12H Price

Specifications of CM20TF-12H

Voltage – Collector Emitter Breakdown (Max) 600V

Vce(on) (Max) @ Vge, Ic 2.8V @ 15V, 20A

Supplier Device Package Module

Series IGBTMOD™

Power – Max 125W

Package / Case Module

Operating Temperature -40°C ~ 150°C (TJ)

NTC Thermistor No

Mounting Type Chassis Mount

Moisture Sensitivity Level (MSL) 1 (Unlimited)

Lead Free Status / RoHS Status Contains lead / RoHS non-compliant

Input Capacitance (Cies) @ Vce 2nF @ 10V

Input Standard

Detailed Description IGBT Module Three Phase Inverter 600V 20A 125W Chassis Mount Module

Current – Collector Cutoff (Max) 1mA

Current – Collector (Ic) (Max) 20A

CM20TF-12H Six-IGBT IGBTMOD H-Series Module 20 Amperes 600 Volts.

MFG Guide

MFG Guide

What is the component group of the linear motor drive device of the high-speed machining center

2022-05-19 Chinaeye

Nowadays, many high-speed machining centers use linear motors to drive linear three-axes. The way high-speed machining centers use servo motors + rolling screws to drive linear three-axes has gradually decreased. At present, most high-speed machining centers have adopted linear The motor drives the linear three-axis, and the linear motor directly drives the linear three-axis, which […]

MFG Guide

how the gate of plastic mold works

2022-05-19 Chinaeye

The gates of Plastic mold is usually a method or orifice linking the runner to the cavity. It features a little cross-sectional region while it is in contrast to the remainder of the feed method. This little cross-sectional region is required in order that: The entrance freezes right after the cavity is filled in order […]

MFG Guide

Regeneration Of Silicone Oil

2022-05-17 Chinaeye

The chemical properties of silicone oil are relatively warm, but it will also deteriorate after long-term use due to oxidation and foreign impurities. Due to the high price of silicone oil, it should be recycled and regenerated separately. Waste silicone oil is usually regenerated by two methods. The waste silicone oil in electrical equipment is […]

MFG Guide

Can Silicone Gloves Wash Dishes Well?

2022-05-17 Chinaeye

In daily cleaning or washing dishes, you need to do it yourself in many places. When cleaning or washing dishes, you need to use detergent or detergent. These things are harmful to human skin and are unprofitable. If you soak in water for a long time, the skin on your hands will become worse and […]

MFG Guide

Internal stress and warping

2022-05-16 Chinaeye

Internal stress and warping When thick sections are moulded，rapid changes in temperature can cause thermally induced stresses due to differential expansion. If surface layers cool faster than the interior through poor conduction, the contraction of the surface will be greater than the interior thereby setting up stresses which can lead to warping and even failure […]

Cnc Machining

Cnc Machining

How to measure the surface roughness of large parts?

2021-12-27 Chinaeye

Large parts, such as the engine block of emergency generators, construction machinery or ship engines; truck steering knuckles; or gears and bearings used in wind generators are usually too large and heavy to be performed on fixed roughness measurement equipment Measurement. Nevertheless, the roughness parameters must still be tested. In fact, roughness measurements on large […]

Cnc Machining

How to avoid bubbles or holes in the 3D printing manufacturing process?

2021-12-27 Chinaeye

Laser powder bed fusion is the dominant additive manufacturing technology and has not yet reached its potential. The problem facing the industry is that sometimes tiny bubbles or holes are formed during the printing process, and these holes form weak points in the final product. In the 3D printing process of parts, when the low-speed […]

Cnc Machining

How to choose the best grinding process for 3D printed parts

2021-12-27 Chinaeye

For metal production parts manufactured by additive manufacturing (AM), post-processing is usually required, especially on functional surfaces. Abrasive machining including grinding and polishing has the ability to finish machining conventional parts and additive parts (ie, 3D printed parts). Compared with mechanical processing (such as milling and other alternative finishing processes), grinding has the advantage of […]

Cnc Machining

Cooperative team to solve machine tool supply chain problems: 3D printing may be the first choice

2021-12-27 Chinaeye

A cooperative team from Oak Ridge National Laboratory solved the problem of the machine tool supply chain. The first step: 3D printing the largest casting. In remote laboratories, scientists and engineers representing public and private companies are working to restore and stabilize the dominance of American manufacturing. The purpose is not to solve the problems […]

Cnc Machining

The Magnesium Alloy Application In Bicycle Frame

2021-12-27 Chinaeye

The density of magnesium alloy is 1.7, which is only 21% of steel and 60% of aluminum alloy. The advantages of lightweight are very obvious. In addition, magnesium alloy has a series of advantages, in the application of bicycles, it has high rigidity and high bending resistance; excellent shock absorption, absorbing shock and vibration. The […]