Electronic

Semikron SKKT57/16E New Stock

2021-10-05 die casting Comments Off

#SKKT57/16E Semikron SKKT57/16E New 57A/1600V/SCR/2U SKKT 57/16E Thyristor / Diode Module Series Connected 50 A 1600 V, SKKT57/16E pictures, SKKT57/16E price, #SKKT57/16E supplier
——————————————————————-
Email: [email protected]

https://www.slw-ele.com/skkt57-16e.html

——————————————————————-

The SKKT 57/16 E is a 7-pin Thyristor/Diode Module with heat transfer through aluminum oxide ceramic isolated metal baseplate. Hard soldered joints for high reliability. The thyristor/diode module is equipped with SEMIKRON chips.

SEMIPACK 1 housing

Applications

Motor Drive & Control, Microwave, Lighting

SCR Module Type: Series Connected – SCRs

Peak Repetitive Off-State Voltage, Vdrm: 1.6kV

Gate Trigger Current Max, Igt: 150mA

Current It av: 50A

On State RMS Current IT(rms): 95A

Peak Non Rep Surge Current Itsm 50Hz: 1.5kA

Holding Current Max Ih: 250mA

Gate Trigger Voltage Max Vgt: 3V

Operating Temperature Max: 125°C

57A/1600V/SCR/2U SKKT 57/16E Thyristor / Diode Module Series Connected 50 A 1600 V

MFG Guide

MFG Guide

Prevents black mold spots on plant leaves

2023-03-22 Chinaeye

Coal pollution disease, also known as coal smoke disease, is common in flowers and trees, affecting photosynthesis, reducing ornamental value and economic value, and even causing death. Pay attention to prevention and control in garden maintenance. Symptoms: The symptom is the formation of small black mold spots on the leaf surface and branch tips, which […]

MFG Guide

2011-02-26 14:03 Increased demand for woodworking machinery

2023-03-22 Chinaeye

2011-02-26 14:03Increased demand for woodworking machinery VIncreased demand for woodworking machinery Please keep the source and address of this article for reprinting：2011-02-26 14:03 Increased demand for woodworking machinery Reprint Statement: If there are no special instructions, all articles on this site are original. Please indicate the source for reprinting.：Cnc Machine Wiki，Thanks

MFG Guide

Advantages Of Silicone Kitchenware

2023-03-21 Chinaeye

As we all know, consciousness of "green" & environmental friendly nowadays have gradually become a trend. And eco-friendly silicone products are becoming more and more customer's choice.Under this trend, silicone are widely used in industry, including kitchenware kitchen supplies industry.What are advantages of silicone kitchenware?Silicone material is a new type of material for kitchen utensils […]

MFG Guide

Two-Color, Dual-Hardness LSR Molding

2023-03-20 Chinaeye

At the recent K 2007 show in Dusseldorf, a Swiss custom molder illustrated the trend toward multi-component molding with liquid silicone rubber (LSR). Silcotech AG of Stein am Rhein, molded a baby pacifier that combined two colors and hardnesses of LSR in one part. The two materials were injected sequentially in one cycle without opening […]

MFG Guide

Silicone sealing ring-the important component of solar heater

2023-03-20 Chinaeye

As the major component-silicone sealing ring, it quality is very important. As we all known that solar heater is applied to outdoor place, it must be undergo very worst environment. In the south areas, the temperature of solar heater tank can be reach at 140º, and on the contrary, at the north areas, the […]

Cnc Machining

Cnc Machining

High-quality plastic parts can be manufactured using pyrometers

2022-06-26 Chinaeye

Plastic parts are vital in many different industries. New combinations of materials and manufacturing technologies are being developed, especially in challenging applications such as automotive engineering. Continuous fiber-reinforced thermoplastics are a common example of this innovation, which is extremely strong and lightweight at the same time. Automotive engineering is one such field, providing a series […]

Cnc Machining

How to measure the surface roughness of large parts?

2021-12-27 Chinaeye

Large parts, such as the engine block of emergency generators, construction machinery or ship engines; truck steering knuckles; or gears and bearings used in wind generators are usually too large and heavy to be performed on fixed roughness measurement equipment Measurement. Nevertheless, the roughness parameters must still be tested. In fact, roughness measurements on large […]

Cnc Machining

How to avoid bubbles or holes in the 3D printing manufacturing process?

2021-12-27 Chinaeye

Laser powder bed fusion is the dominant additive manufacturing technology and has not yet reached its potential. The problem facing the industry is that sometimes tiny bubbles or holes are formed during the printing process, and these holes form weak points in the final product. In the 3D printing process of parts, when the low-speed […]

Cnc Machining

How to choose the best grinding process for 3D printed parts

2021-12-27 Chinaeye

For metal production parts manufactured by additive manufacturing (AM), post-processing is usually required, especially on functional surfaces. Abrasive machining including grinding and polishing has the ability to finish machining conventional parts and additive parts (ie, 3D printed parts). Compared with mechanical processing (such as milling and other alternative finishing processes), grinding has the advantage of […]

Cnc Machining

Cooperative team to solve machine tool supply chain problems: 3D printing may be the first choice

2021-12-27 Chinaeye

A cooperative team from Oak Ridge National Laboratory solved the problem of the machine tool supply chain. The first step: 3D printing the largest casting. In remote laboratories, scientists and engineers representing public and private companies are working to restore and stabilize the dominance of American manufacturing. The purpose is not to solve the problems […]